Your Adsense Link 728 X 15

tugas pertama jarkom lll

Posted by Kyer 99 Selasa, 26 Maret 2013 0 komentar


Perintah dasar show pada router
topologi jaringan



NO
PERINTAH PENUH
PERINTAH SINGKAT
FUNGSI PERINTAH
1
Show startup-config
Sh st
Menampilkan isi file konfigurasi yang tersimpan di NVRAM
2
Show running-config
Sh ru
Menampilkan konfigurasi yang sedang berjalan di RAM. Termasuk hostname,passwords,interface IP addresses,routing protocol yang aktif,DHCP dan konfigurasi NAT
3
Show interfaces
Sh in
Menunjukkan interface yang berjalan di router
4
Show arp
-
Menampilkan dan memodifikasi resolusi alamat
5
Show IP route
Sh ip ro
Memperlihatkan konfigurasi routing
6
Show users
Sh u
Menampilkan seluruh user yang terhubung ke router
7
Show versions
Sh v
Menampilkan informasi tentang versi software yang sekarang sedang berjalan, lengkap dengan informasi hardware dan devicenya
sekarang sedang berjalan, lengkap dengan informasi hardware dan devicenya


katagori perintah dasar "show" pada router:


Pertama kali ketikkan enable untuk masuk ke mode admin/root pada router, hingga terjadi berubah tampilan dari Router> menjadi Router#, perintah dasar yang cukup sering digunakan adalah show, coba ketikkan show ? untuk mengetahui apa saja yang dapat dijalankan pada perintah show. Misalkan ketikkan perintah show version untuk mengetahu versi dari IOS Router yang digunakan, maka akan muncul tampilan  Kini anda dapat mencicipi mengkonfigurasi Router Cisco dengan praktis dan tentu saja gratis. Selamat mencoba dan belajar. 


Perintah penuh
Perintah singkat
Maksud Perintah
show running-config
sh ru/run
Menampilkan konfigurasi yang sedang berjalan di RAM. Termasuk host name, passwords, interface IP addresses, routing protocol yang aktif, DHCP dan konfigurasi NAT. Dapat dijalankan di EXEC mode.
show startup-config
Sh st/sta
Menampilkan isi file konfigurasi yang tersimpan di NVRAM,Mulai dariHost Name, Passwords, Interface IP Addresses, Routing Protocol yang aktif, DHCP dan konfigurasi NAT.
Show version
Sh v/ver
Menampilkan informasi tentang versi software yang sekarang sedang jalan lengkap dengan informasi hardware dan devicenya.
show ip protocols
Sh ip p/pro
Memperlihatkan ip protokol routing yang telah dikonfigurasi dan sedang berjalan,
Digunakan untuk menampilkan status interface IP,baik secara global maupun khusus dari protokol yang terkonfigurasi pada saat ini (konfigurasi IP awal).
show ip route
Sh ip ro
Memperlihatkan konfigurasi routing,
Digunakan untuk menampilkan konfirmasi pada Router yang telah di authentikasi oleh Router lain dan telah mampu memperoleh rute dari Router lainnya, selain itu juga digunakan untuk mengetahui konfigurasi IP yang dilakukan baik secara global maupun secara khusus dari IYN. Yang meliputi configurasi IP  pada FastEthernet0/0 maupun pada IP Serial2/0
show interfaces
Sh in/int
Menunjukkan interface yg berjalan di router,
Digunakan untuk menampilkan statistic semua interface IYN mulai dari FastEthernet dan Serial. Untuk menampilkan statistic interface tertentu, menggunakan perintah show interfaces diikuti dengan nomor port/slot interface, contoh : Andhika#show interfaces serial 0/1
show ip interface brief
Sh ip i b
Tinjauan semua antarmuka pada router,
Digunakan untuk menampilkan Konfigurasi pada interface yang terhubung pada IYN. Mulai dari konfigurasi yang sedang berjalan maupun yang konfigurasi yang tidak berjalan (belum terkonfigurasi). Pada perintah ini kita dibawa untuk mengetahui : Interface, IP-Address, Method, Status, Protocol
show protocols
Sh prot
menampilkan status interface baik secara global maupun khusus dari protokol layer 3 yang terkonfigurasi.
show cdp neighbors
Sh cd ne/cdp
Menampilkan ringkasan cdp perangkat tersambung,
Digunakan untuk mengetahui Capability Codes, yang meliputi : R (IYN), T (Trans Bridge), B (Source Route Bridge), S (Switch), H (Host), I (IGMP), r (Repeater), P (Phone). Selain itu juga digunakan untuk mengetahui Device ID diantaranya : Local Intrfce, Holdtme, Capability, Platform, Port ID
show sessions
Sh se
Memperlihatkan sesi yang ada sekarang
Digunakan untuk mengetahui koneksi yang sedang berjalan (koneksi yang di buka)
show ssh
Sh ss
Menampilkan operasi status pengoperasian SSH
Digunakan untuk melakukan koneksi dengan server SSHv2 dan SSHv1
ping
P
Digunakan untuk melakukan / melihat koneksi antar jaringan yang sedang berhubungan. Perintah ping harus diikuti address or hostname. Contoh ; ping 192.168.1.1,
Memastikan apakah suatu komputer tertentu dalam suatu jaringan atau internet itu ada dan terhubung.
Traceroute
tr
Menunjukkan rute yang dilewati paket untuk mencapai tujuan. Ini dilakukan dengan mengirim pesan Internet Control Message Protocol (ICMP) Echo Request Ke tujuan dengan nilai Time to Live yang semakin meningkat.
contoh penggunaan "show" pada router

LETTO #sh ru
Building configuration...
Current configuration : 702 bytes!version 12.2no service timestamps log datetime msecno service timestamps debug datetime msecno service password-encryption!hostname ANDHIKA!!!!!!!!!!!!!!!!interface FastEthernet0/0 no ip address duplex auto speed auto shutdown!interface FastEthernet1/0 ip address 192.168.3.2 255.255.255.0 duplex auto speed auto!interface Serial2/0 no ip address shutdown!interface Serial3/0 ip address 192.168.2.2 255.255.255.0!interface FastEthernet4/0 no ip address shutdown!interface FastEthernet5/0 no ip address shutdown!ip classlessip route 0.0.0.0 0.0.0.0 Serial3/0 !!!!!!!!!line con 0line vty 0 password 12345 loginline vty 1 4 login!!!end
LETTO #sh sta
startup-config is not present
LETTO #sh sta
startup-config is not presentANDHIKA#sh verCisco Internetwork Operating System SoftwareIOS (tm) PT1000 Software (PT1000-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2005 by cisco Systems, Inc.Compiled Wed 27-Apr-04 19:01 by miwangImage text-base: 0x8000808C, data-base: 0x80A1FECC
ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)Copyright (c) 2000 by cisco Systems, Inc.ROM: PT1000 Software (PT1000-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)
System returned to ROM by reloadSystem image file is "flash:pt1000-i-mz.122-28.bin"
PT 1001 (PTSC2005) processor (revision 0x200) with 60416K/5120K bytes of memory.Processor board ID PT0123 (0123)PT2005 processor: part number 0, mask 01Bridging software.X.25 software, Version 3.0.0.4 FastEthernet/IEEE 802.3 interface(s)2 Low-speed serial(sync/async) network interface(s)32K bytes of non-volatile configuration memory.63488K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
LETTO #sh ip pro
LETTO #sh ip ro
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area       * - candidate default, U - per-user static route, o - ODR       P - periodic downloaded static route
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
C    192.168.2.0/24 is directly connected, Serial3/0C    192.168.3.0/24 is directly connected, FastEthernet1/0S*   0.0.0.0/0 is directly connected, Serial3/0
LETTO #sh int
FastEthernet0/0 is administratively down, line protocol is down (disabled)  Hardware is Lance, address is 0001.c71b.5e5d (bia 0001.c71b.5e5d)  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,     reliability 255/255, txload 1/255, rxload 1/255  Encapsulation ARPA, loopback not set  ARP type: ARPA, ARP Timeout 04:00:00,   Last input 00:00:08, output 00:00:05, output hang never  Last clearing of "show interface" counters never  Input queue: 0/75/0 (size/max/drops); Total output drops: 0  Queueing strategy: fifo  Output queue :0/40 (size/max)  5 minute input rate 0 bits/sec, 0 packets/sec  5 minute output rate 0 bits/sec, 0 packets/sec     0 packets input, 0 bytes, 0 no buffer     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort     0 input packets with dribble condition detected     0 packets output, 0 bytes, 0 underruns     0 output errors, 0 collisions, 2 interface resets     0 babbles, 0 late collision, 0 deferred     0 lost carrier, 0 no carrier     0 output buffer failures, 0 output buffers swapped outFastEthernet1/0 is up, line protocol is up (connected)  Hardware is Lance, address is 0060.5cca.d984 (bia 0060.5cca.d984)  Internet address is 192.168.3.2/24  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,     reliability 255/255, txload 1/255, rxload 1/255  Encapsulation ARPA, loopback not set  ARP type: ARPA, ARP Timeout 04:00:00,   Last input 00:00:08, output 00:00:05, output hang never  Last clearing of "show interface" counters never  Input queue: 0/75/0 (size/max/drops); Total output drops: 0  Queueing strategy: fifo  Output queue :0/40 (size/max)  5 minute input rate 1 bits/sec, 0 packets/sec  5 minute output rate 1 bits/sec, 0 packets/sec     89 packets input, 3621 bytes, 0 no buffer     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort     0 input packets with dribble condition detected     85 packets output, 3920 bytes, 0 underruns     0 output errors, 0 collisions, 0 interface resets     0 babbles, 0 late collision, 0 deferred     0 lost carrier, 0 no carrier     0 output buffer failures, 0 output buffers swapped outSerial2/0 is administratively down, line protocol is down (disabled)  Hardware is HD64570  MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,     reliability 255/255, txload 1/255, rxload 1/255  Encapsulation HDLC, loopback not set, keepalive set (10 sec)  Last input never, output never, output hang never  Last clearing of "show interface" counters never  Input queue: 0/75/0 (size/max/drops); Total output drops: 0  Queueing strategy: weighted fair  Output queue: 0/1000/64/0 (size/max total/threshold/drops)     Conversations  0/0/256 (active/max active/max total)     Reserved Conversations 0/0 (allocated/max allocated)     Available Bandwidth 96 kilobits/sec  5 minute input rate 0 bits/sec, 0 packets/sec  5 minute output rate 0 bits/sec, 0 packets/sec     0 packets input, 0 bytes, 0 no buffer     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort     0 packets output, 0 bytes, 0 underruns     0 output errors, 0 collisions, 2 interface resets     0 output buffer failures, 0 output buffers swapped out     0 carrier transitions     DCD=down  DSR=down  DTR=down  RTS=down  CTS=downSerial3/0 is up, line protocol is up (connected)  Hardware is HD64570  Internet address is 192.168.2.2/24  MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,     reliability 255/255, txload 1/255, rxload 1/255  Encapsulation HDLC, loopback not set, keepalive set (10 sec)  Last input never, output never, output hang never  Last clearing of "show interface" counters never  Input queue: 0/75/0 (size/max/drops); Total output drops: 0  Queueing strategy: weighted fair  Output queue: 0/1000/64/0 (size/max total/threshold/drops)     Conversations  0/0/256 (active/max active/max total)     Reserved Conversations 0/0 (allocated/max allocated)     Available Bandwidth 96 kilobits/sec  5 minute input rate 0 bits/sec, 0 packets/sec  5 minute output rate 0 bits/sec, 0 packets/sec     5 packets input, 440 bytes, 0 no buffer     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort     4 packets output, 412 bytes, 0 underruns     0 output errors, 0 collisions, 0 interface resets     0 output buffer failures, 0 output buffers swapped out     0 carrier transitions     DCD=up  DSR=up  DTR=up  RTS=up  CTS=upFastEthernet4/0 is administratively down, line protocol is down (disabled)  Hardware is Lance, address is 0009.7c10.a5ca (bia 0009.7c10.a5ca)  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,     reliability 255/255, txload 1/255, rxload 1/255  Encapsulation ARPA, loopback not set  ARP type: ARPA, ARP Timeout 04:00:00,   Last input 00:00:08, output 00:00:05, output hang never  Last clearing of "show interface" counters never  Input queue: 0/75/0 (size/max/drops); Total output drops: 0  Queueing strategy: fifo  Output queue :0/40 (size/max)  5 minute input rate 0 bits/sec, 0 packets/sec  5 minute output rate 0 bits/sec, 0 packets/sec     0 packets input, 0 bytes, 0 no buffer     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort     0 input packets with dribble condition detected     0 packets output, 0 bytes, 0 underruns     0 output errors, 0 collisions, 2 interface resets     0 babbles, 0 late collision, 0 deferred     0 lost carrier, 0 no carrier     0 output buffer failures, 0 output buffers swapped outFastEthernet5/0 is administratively down, line protocol is down (disabled)  Hardware is Lance, address is 0002.4a72.39ca (bia 0002.4a72.39ca)  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,     reliability 255/255, txload 1/255, rxload 1/255  Encapsulation ARPA, loopback not set  ARP type: ARPA, ARP Timeout 04:00:00,   Last input 00:00:08, output 00:00:05, output hang never  Last clearing of "show interface" counters never  Input queue: 0/75/0 (size/max/drops); Total output drops: 0  Queueing strategy: fifo  Output queue :0/40 (size/max)  5 minute input rate 0 bits/sec, 0 packets/sec  5 minute output rate 0 bits/sec, 0 packets/sec     0 packets input, 0 bytes, 0 no buffer     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort     0 input packets with dribble condition detected     0 packets output, 0 bytes, 0 underruns     0 output errors, 0 collisions, 2 interface resets     0 babbles, 0 late collision, 0 deferred     0 lost carrier, 0 no carrier     0 output buffer failures, 0 output buffers swapped out
LETTO #sh ip int br
Interface              IP-Address      OK? Method Status                Protocol
FastEthernet0/0        unassigned      YES manual administratively down down
FastEthernet1/0        192.168.3.2     YES manual up                    up
Serial2/0              unassigned      YES manual administratively down down
Serial3/0              192.168.2.2     YES manual up                    up
FastEthernet4/0        unassigned      YES manual administratively down down
FastEthernet5/0        unassigned      YES manual administratively down down
LETTO #sh prot
Global values:  Internet Protocol routing is enabledFastEthernet0/0 is administratively down, line protocol is downFastEthernet1/0 is up, line protocol is up  Internet address is 192.168.3.2/24Serial2/0 is administratively down, line protocol is downSerial3/0 is up, line protocol is up  Internet address is 192.168.2.2/24FastEthernet4/0 is administratively down, line protocol is downFastEthernet5/0 is administratively down, line protocol is down
LETTO #sh cdp ne
Capability Codes: R - ANDHIKA, T - Trans Bridge, B - Source Route Bridge                  S - Switch, H - Host, I - IGMP, r - Repeater, P - PhoneDevice ID    Local Intrfce   Holdtme    Capability   Platform    Port IDANDHIKA       Ser 3/0          168            R       PT1000      Ser 2/0
LETTO #sh ses
% No connections open
LETTO #sh ss
%No SSHv2 server connections running.%No SSHv1 server connections running.
LETTO #ping 192.168.1.1
Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/60 ms
LETTO #tra 192.168.2.1
Type escape sequence to abort.Tracing the route to 192.168.2.1
  1   192.168.2.1     20 msec   20 msec   20 msec

Popular Posts